Unbenannt

<%PostCommentPage%> <%PhotoAlbumPage%> <%ProfilePage%>

Miocropod 2 clone - won the lottery

{ 10:00, 27 April 2018 } { 0 comments } { Link }
I won the lottery!
I bought my miocropod 2 clone from http://www.obdexpress.co.uk/wholesale/witech-micropod-2-diagnostic-programming-chrysle.html, same as what Radius bought. It came with a hard drive that is barely working. Its making beeping sounds and clicking and on its very last legs. I was able to make a backup though and there is actually a second partition on it with an Acronis backup image already created from 8/15/17. Anyway I will have to contact the seller and arrange for some discount since the hard drive is virtually useless.
Anyway, the main thing is that the miocropod 2 had the required circuits etc, and the DRB3 works after following most of Radius’s instructions. I had to change it up since I did follow his instructions exactly, but the flexnet update didn’t work, and so it failed and the drb3 did not work.
In order to get it to work, I had to change the date. In the beginning when installing the stubs, his directions had already instructed you to change the date to 1/1/17, then navigate to the folder and install the three stubs. Reboot. Try to use flexnet connect to update but it failed. Windows update also errored because of the wrong date. So I changed the date to the correct date. Now flexnet connect worked and I was able to update K-line and enhanced drb3. As soon as both had updated, I disconnected internet and then changed date back to 1/1/17. Then I followed the rest of the instructions. Plugged in the pod, waited for windows to see it and make the virtual network, and then launched wiTech. Launched enhanced drb3. Success!! It works!!
So the instructions are good, but at least for me, I had to fix the date to the correct date to get the flexnet updates. Once updated, disconnect the internet and change the date back to 1/1/17 for it to work.

Radius’s instructions: the thread from http://mhhauto.com/Thread-Verified-Clone-Micropod-2-working-with-DRB-Emulation

The device I purchased is an OFFLINE ONLY version of micropod 2, but I only use it for diagnostics, not for programming as I do not have a TechAuthority account. So if you need one for online use this is not the unit to buy.
These are the steps I followed to get Enhanced DRB III Emulator to work:
1: Make a backup copy of the partition from the hard drive included with the micropod!
2: Install HDD in laptop
3: Set date to 01/01/17 BEFORE booting from laptop
4: Boot to HDD
5: Allow windows to install drivers, etc, as needed for your laptop and reboot as needed.
6: Once all of that is done, do NOT run WiTech yet!
7: Turn OFF internet!
8: Navigate to C:\ProgramData\wiTECH\jserver\data\core\stubs
9: Install DRB Emulator stub
10: Install DRB Enhanced emulator stub
11: Install K-Line stub
12: Reboot computer
13: Set date back to current date
14: ALLOW internet access
15: Run Flexnet software updater. Do NOT update WiTech!!!
16: Flexnet will find updates for enhanced DRB and K-Line
17: Install K-Line update first
18: Install Enhanced update next.
19: Turn date back to 01/01/17!
20: Once updates and downloaded and installed, turn OFF internet and NEVER turn on again!
21: Reboot computer
22: Attach Micropod to car. When green LED turns on, turn on car ignition
23: Attach USB cable to PC and Micropod
24: When Windows is done installing drivers, etc, you should show a network connection in the tool tray with no internet access
25: Run Wi-Tech
26: Press “Launch DRB III” button in lower right hand corner
27: Accept EULA
28: DRB Emulator will launch.
29: Enjoy.

UPDATE:
I already tested it on a 2010 Charger under witech and works flawlessly, and got a 2004 Dodge pickup and under the emulator worked perfectly. I already called my locksmith, who drives an 04 Sprinter to try it as well.

Src:
http://blog.obdexpress.co.uk/2018/04/27/miocropod-2-clone-won-the-lottery-d/

{ Kommentar schreiben }

{ Last Page } { Page 71 of 86 } { Next Page }

ber Mich

Start
Mein Profil
Archiv
Freunde
Mein Photo Album

«  December 2018  »
MonTueWedThuFriSatSun
 12
3456789
10111213141516
17181920212223
24252627282930
31 

Links


Kategorien


Letzte Beitrge

How to clone ID48 96bits with Xhorse VVDI key tool?
Use Xtool Anyscan A30 diagnose Audi A6 2011 with an iPhone
How does Ktag KTM100 work with Mercedes ME9.7 ECU and Renew Cable?
Can I buy Lonsdor K518ise for BMW CAS keys only?
How to change a language for Diagbox 7.83

Freunde