Unbenannt

<%PostCommentPage%> <%PhotoAlbumPage%> <%ProfilePage%>

How to read an SD card for Kess 5.017 or create a new one

{ 03:05, 17 January 2019 } { 0 Kommentare } { Link }
Guide:How to read an SD card for Kess 5.017 or create a new one

128 MB XOR Key01-13.zip
https://mega.nz/#!kRxTwQxZ!Vw6g3ROBHr9w7aboGEe97UPIbv2ruVOvlLIZaH1HPDY
Zip Password = "kess5017"

Note: Only Kess 5.017 or 5.028, not for 3.099 etc.

Have the instructions for new SD cards:
You need :
WinHex and XorFiles v1.0 http://www.nirsoft.net/utils/xorfiles.html
Insert your Original SD-Card to Cardreader on PC.
Run WinHex, press F9 open Disk, read your SD-card.
Mark 208Bytes = 13 lines from 0x00000270 to 0x0000033F.
kess-5-017- create-a-new-sd-card-01


Copy 13 lines to new file.
Open in WinHex my Keyfile “128 MB XOR Key01-13.img”
Search and replace line 1 in your Keyfile with all line1 lines in “128 MB XOR Key01-13.img”
Search and replace line 2 in your Keyfile with all line2 lines in “128 MB XOR Key01-13.img”
….............................
Search and replace line 13 in your Keyfile with all line13 lines in “128 MB XOR Key01-13.img”
kess-5-017- create-a-new-sd-card-02

Save your new 128 MB XOR Key01-13.img
run XorFiles v1.0
Filename 1: = your original SD-Imagefile
Filename 2: = your new createt “SD128 MB XOR Key01-13.img” (with your 13 lines ;-)
Destination: = any filename for your new uncryptet Imagefile
kess-5-017- create-a-new-sd-card-03


if you have decrypted the files, you can integrate the decryptet image file with "ImDisk Virtual Disk
Driver" as a virtual drive and save the files to the PC.
Link to ImDisk https://sourceforge.net/projects/imdisk-toolkit/
If you want to use any new SD-Card in your Kess 5017, use Winhex to fill the SD-card with 00 .
put SD-card in Kess, power on Kess.
The 13-line KEY = 208 Bytes is x times on the SD.
From 0x000000D0 it is on some empty SD cards.
If you not found search any other line.
It is important that from line 0 always the 13 lines are
13, 26, 39, 52 ..... 4160 ..... 344032 etc.
that is, 0x0001040 is in decimal 4160,
13 rows = 208 bytes,
4160 divided by 208 = 20
Or 53FE0 = decimal 344032
344032 divided by 208 = 1654
that means if you think you have found the key you have to divide the address (decimal) by 208
without anything after comma.
then the start same Procedur to create a new “SD128 MB XOR Key01-13.img” file with new SDCard
Key.
Format the new SD-card with FAT , copy Files to SD-ard and crypt it with “XorFiles

http://blog.obdexpress.co.uk/2019/01/17/kess-5-017-how-to-read-sd-card-or-create-a-new-sd-card/

How to copy UID /CUID card with Handy Baby II?

{ 06:49, 15 January 2019 } { 0 Kommentare } { Link }
Step-by-step guide of Using a JMD Handy Baby II to read a locked UID /CUID card, then decode and finally copy it into a blank UID /CUID successfully.

Steps:
Open JMD Handy baby 2.
jmd-handy-baby-ii-copy-ic-card-01

Choose “Card-CP”.
jmd-handy-baby-ii-copy-ic-card-2

Put the IC card on the back.
jmd-handy-baby-ii-copy-ic-card-3jmd-handy-baby-ii-copy-ic-card-4

You can see it’s locked.
jmd-handy-baby-ii-copy-ic-card-5
Now use JMD Handy Baby II APP to decode.
Firstly, open the Baby II Bluetooth.
jmd-handy-baby-ii-copy-ic-card-6
Press “Ok” to decode.
jmd-handy-baby-ii-copy-ic-card-7

Calculating, don’t move away this card.
It displays “On-line (APP) and the next option is “on-line(PC)”.
jmd-handy-baby-ii-copy-ic-card-7

Open the phone Bluetooth, come to the APP menu.
jmd-handy-baby-ii-copy-ic-card-8
Calculating…
jmd-handy-baby-ii-copy-ic-card-9

Calculate succeed.
jmd-handy-baby-ii-copy-ic-card-10
Use another blank card to copy.
Put into blank UID /CUID
Press “Ok” to copy.
jmd-handy-baby-ii-copy-ic-card-11jmd-handy-baby-ii-copy-ic-card-12jmd-handy-baby-ii-copy-ic-card-13jmd-handy-baby-ii-copy-ic-card-14

Done.
Thanks

Source:
http://blog.obdexpress.co.uk/2019/01/15/how-to-copy-uid-cuid-card-with-jmd-handy-baby-ii/


Galletto V54 0475 is better than fgtech V54 0386: win7 works + more models

{ 08:14, 7 January 2019 } { 0 Kommentare } { Link }
Newest FGTech Galletto V54 with serial number 0475 is much powerful than fgtech V54 with serial number 0386, it adds dozens of car models with checksum working great.

FGTech Galletto V54  0386
Why update FGTech Galletto V54 SN 0475 instead of old one with SN 0386?
  1. I just checked it and 0475 is Euro version, better one than the 0386, but it has different hardware compare to 0386 (Chinese).
  2. Reprogram to 0475 and then you can use better software and also windows 7/10 32/64 bit OS.
  3. 0475 works well with Windows 7/10 32/64 bit OS.
  4. All you who has date changing problems or dont work windows 7 or windows 10 OS, update your tool from 0386 to 0475. Then all these issues are gone!!!!
FGTech Galletto V54 SN 0475

FGTech Galletto V54 SN 0475 new workable models that 0386 doesn’t have:
11/12 – OBD driver SSangyong Delphy DCM3.7 Read/Write, Checksum
11/12 – OBD driver for Ferrari 458 Italia MED9.6 Ecu Master and ECU Slave Read/Write, Checksum
10/12 – OBD driver for Fiat/Alfa/Lancia Twinair/Multiair 8GMF and 8GSF Read/Write, Checksum
10/12 – OBD driver for Mazda 5, Mazda 6 2.0 Diesel ECU RF8x Read/Write, Checksum
10/12 – OBD driver for Mazda 5, Mazda 6 2.0 Diesel ECU RF7x Read/Write, Checksum
09/12 – OBD driver for Simos 10.xx VAG 1.2 TSI Read/Write, Checksum
09/12 – OBD driver for CRD 3.xx Mercedes 2200 CDI Read/Write, Checksum
09/12 – Simos PCR2.1 VAG 1.6 TDI Unlock Boot Tool – Read/Write EEPROM
09/12 – OBD driver Simos PCR2.1 VAG 1.6 TDI Read/Write, Checksum
08/12 – RSA recognition Peugeot Bipper
08/12 – RSA recognition Citroen Nemo
08/12 – OBD driver Driver for writing Bosch EDC16C34/5 Peugeot Bipper Read/Write, Checksum
08/12 – OBD drive Driver for writing Bosch EDC16C34/5 Citroen Nemo  Read/Write, Checksum
07/12 – OBD driver Delphi DCM3.5 for Tata Safari  Read/Write, Checksum
07/12 – Checksum recognition for DCM3.7 Ssangyong
07/12 – Checksum recognition for DCM3.7 Opel and Saab
07/12 – Checksum recognition for DCM3.7 Kia  and Hyundai
07/12 – Boot Visteon ST10F275 RX-TX Mode
07/12 – Boot ME7.9.10 ST10F275 RX-TX Mode
06/12 – Checksum recognition for Denso Subaru Tribeca
06/12 – Boot Mitsubishi MH7203 Hyundai
06/12 – Checksum recognition for Denso Nissan L200
06/12 – Checksum recognition for Denso Nissan X-Trail
06/12 –  OBD driver Opel Simtec75 CAN  Read/Write, Checksum
05/12 – OBD driver  Porsche SDI3 CAN  Read/Write, Checksum
05/12 – Corvette Utility CAN for change VIN, Code Align, Erase Errors
05/12 – Corvette Utility VPN for change VIN, Code Align, Erase Errors
05/12 – OBD driver Renault SID305 CAN  Read/Write, Checksum
05/12 – OBD driver Maserati ME9 CAN  Read/Write, Checksum
04/12 – Tool Boot Hitaci Phase 3
04/12 – Tool Boot Hitaci Phase 2
04/12 – OBD driver Fiat ME17.31 CAN  Read/Write, Checksum
04/12 – Boot Mitsubishi for L200 MH8102F
03/12 – Boot Mitsubishi for Lancer EVO MH7202
03/12 – Fiat MJ8DF CAN Serial Injectors
03/12 – Fiat MJ8DF CAN Serial Injectors
02/12 – OBD driver Fiat MJ8DF CAN  Read/Write, Checksum
02/12 – OBD driver Fiat MJ8DF K-line  Read/Write, Checksum
02/12 – OBD driver Mercedes Delphi CRD2.xx CAN  Read/Write, Checksum
01/12 – OBD driver Ford Delphi DCM3.5 CAN Read/Write, Checksum
01/12 – OBD driver PSA Delphi DCM3.5 CAN  Read/Write, Checksum
01/12 – OBD driver VAG Simos 3xx Boot mode 29F400 C167 Read/Write, Checksum
12/11 – OBD driver VAG Simos 9.1 Boot mode 29F400 C167 Read/Write, Checksum
12/11 – OBD driver VAG Simos 7.1 Boot mode 29F400 C167 Read/Write, Checksum
12/11 – OBD driver VAG Simos 33 K-line serial Read/Write, Checksum
12/11 – OBD driver VAG Simos 32 K-line serial Read/Write, Checksum
12/11 – OBD driver VAG Simos 3PG K-line serial Read/Write, Checksum
12/11 – OBD driver VAG Simos 3PE K-line serial Read/Write, Checksum
12/11 – OBD driver VAG Simos 3PD K-line serial Read/Write, Checksum
12/11 – OBD driver VAG Simos 3PC K-line serial Read/Write, Checksum
12/11 – OBD driver VAG Simos 3PA K-line serial Read/Write, Checksum
12/11 – OBD driver VAG Simos 9.1 K-line Read/Write, Checksum
11/11 – JTAG MPC55xx
10/11 – New password Tricore Tprot V08-10
10/11 –  OBD driver Renault Valeo V40, Read/Write, Checksum
10/11 – AUD Renesas

For the old Fgtech V54 with serial number 0386, it was already tested working fine with many car models & ECU types.
old Fgtech V54 reviews
old Fgtech V54 reviews

old Fgtech V54 reviews

Where to have FGTech Galletto V54 with serial number 0475?
It can’t be more better than www.obdexpress.co.uk with helpful and kind customer service and after-sale service.



How to use Yanhua ACDP to program MQB all keys lost?

{ 03:04, 7 January 2019 } { 0 Kommentare } { Link }
Yanhua ACDP basic module + module 6 + PCF-key adapter is one solution for VAG MQB all keys lost programming without soldering. This post is on how to operate.

MQB all keys lost, you need:
Yanhua Mini ACDP newest version 1.0.22.32
Module 6 Volkswagen MQB authorization
PCF-key adapter (payable)
yanhua-mini-acdp-newest-version-01

yanhua-mini-acdp-mqb-immo-02

pcf-key-adapter-03


The following VAG MQB models are covered by Yanhua ACDP: 
A3: MQB 2014.06-
Q2: MQB 2014.06-
Seat Ibiza: MQB 2014.06-
Seat Leon: MQB 2014.06-
Seat Toledo: MQB 2014.06 –
Fabia: MQB 2014.06-
Octavia: MQB 2014,06-
Rapid: MQB 2014.06
Superb: MQB 2014.6 –
Golf: MQB 2014.6 –
Passat B8: MQB 2014.6 –
Polo: MQB 2014.6 –
Tiguan: MQB 2014.6 –
Touran: MQB 2014.6 –
Steps:
Click on “VW”, then “MQB platform instrument”.
yanhua-mini-acdp-mqb-immo-04


Instrument with NEC35xx (Continental / VDO).
yanhua-mini-acdp-mqb-immo-04


IMMO
yanhua-mini-acdp-mqb-immo-05


IMMO menu
yanhua-mini-acdp-mqb-immo-07


For details, you can watch this video

That’s all

Thanks
http://blog.obdexpress.co.uk/2019/01/05/how-to-use-yanhua-acdp-to-program-mqb-all-keys-lost/


Porsche Panamera 2012 odometer correction with OBDSTAR X300 DP PLUS

{ 03:15, 5 January 2019 } { 0 Kommentare } { Link }
Porsche Panamera 2012 odometer correction is done with OBDSTAR DP PLUS (Key Master) via OBD in 2 minutes. How does it work? Go on reading the follow parts. Steps: 1. Turn on ignition, plug OBDSTAR DP PLUS into the OBD port of Porsche Panamera 2012. Tap "Diag Program". 2. Tap "Cluster Calibrate", scroll the screen and find out Porsche. 3. Enter Porsche menu, it displays the newest version. 4. VCI is upgrading Initializing Initializing diagnostic data... Authorizing... 5. Tap "Panamera", then 2010 6. Enter and choose "Mileage adjustment". 7. Communicating -> Reading data. 8. Please enter a file to save. 9. Make sure the current mileage is correct, and input a new value. 10. Communicating -> Adjustment complete in 2 sends. You can see 71904KM on the dashboard. 11. If you don't want the data recovery, back to choose "Data Recovery". 12. Find out "2012BSXX BIN" I just saved, tap it to enter. Communicating and then get message "Operation success". Then you can see the dashboard display the old value before adjusting. Done. Fact: OBDSTAR DP PLUS has the same capacities and same vehicle coverage as Key Master in green color , that is their difference is only the outlook. And DP plus is sold on eshop like www.obdexpress.co.uk.

http://blog.obdexpress.co.uk/2019/01/03/porsche-panamera-2012-odometer-correction-with-obdstar-dp-plus-key-master/

ber Mich

Start
Mein Profil
Archiv
Freunde
Mein Photo Album

«  January 2019  »
MonTueWedThuFriSatSun
 123456
78910111213
14151617181920
21222324252627
28293031 

Links


Kategorien


Letzte Beitrge

How to read an SD card for Kess 5.017 or create a new one
How to copy UID /CUID card with Handy Baby II?
Galletto V54 0475 is better than fgtech V54 0386: win7 works + more models
How to use Yanhua ACDP to program MQB all keys lost?
Porsche Panamera 2012 odometer correction with OBDSTAR X300 DP PLUS

Freunde